[beeptac]

hi,

i have upgrade my ci box, but the process have failed!!!

now my ci box dont start and reboot (led ALM on and click), reboot...

i have press the reset button but no change.

you know a procedure in order to make a recovery to firmware?

thank in advance

beeptac

babelfish translation.....

bonjour,
j'ai la mise à niveau ma boîte de ci, mais le processus ont échoué ! ! !

maintenant ma boîte de ci ne démarrent pas et ne rechargent pas (ALM mené dessus et clic), la remise à zéro…

j'ai la presse le bouton de remise mais aucun changement.

vous savez un procédé afin de faire un rétablissement aux progiciels ?

merci

beeptac

[Dumboton]

There's no rescvue firmware in teh CI.BOX. The only way is the use of the inside serial port but you need a special cable.

If you are intesrested and you think you able to cope with it I can send you more details.

here some cables
http://www.neufbox4.org/wiki/index.php?title=Port_s%C3%A9rie#Interface_RS232
or a very simple

_________________

CI c'était des hommes, un service et de la qualité

[beeptac]

thanks for your answer...

yes, they are interested to the recovery of the router,
you know to indicate the procedure to me?

[Dumboton]

You need to open the cibox and that is forbiden if you want to keep Neuf-CI's guarantee.

If you call the hotline and you explain that there is a continuous reset of the box you can get an free exchange. (if the cibox s hired)
_________________

CI c'était des hommes, un service et de la qualité

[beeptac]

my ci box is out of warranty and my property.

is a model AH4021 hitachi, i have open the box and found a 4 pin connection named J3

I have followed yours link but it is spoken about an other model?
you have other information with regard to?

setting hyper terminal, ecc.

[Dumboton]

here (registration is required)
http://www.gandf.info/phpBB/viewtopic.php?t=3
more informations about 4 pins on the board


Quel chance, à ma prenière tentative de connection sur la connection serie, le CFE me répond (et donc le cablâge est correcte) et ce avec une interface non adapté.

Voici le brochage :
1 : VCC (3.3V)
2 : PC -> AH4222
3 : AH4222 -> PC
4 : GND (0V)

Je ne suis pas sur du cablage du milieu. De toute façon, nverser les cable ne grille rien.

Voici ce que me répond le modem à son allumage :
Citation:
CFE version 1.0.37-0.7 for BCM96348 (32bit,SP,BE)
Build Date: ¤­ 10¤ë 21 09:34:25 CST 2005 (root@hp)
Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.

Initializing Arena.
Initializing Devices.
Auto-negotiation timed-out
10 MB Half-Duplex (assumed)
CPU type 0x29107: 256MHz, Bus: 128MHz, Ref: 32MHz

Total memory used by CFE: 0x80401000 - 0x80523030 (1187888)
Initialized Data: 0x8041B0E0 - 0x8041C9B0 (6352)
BSS Area: 0x8041C9B0 - 0x80421030 (18048)
Local Heap: 0x80421030 - 0x80521030 (1048576)
Stack Area: 0x80521030 - 0x80523030 (8192)
Text (code) segment: 0x80401000 - 0x8041B0D8 (106712)
Boot area (physical): 0x00524000 - 0x00564000
Relocation Factor: I:00000000 - D:00000000

Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id Name : 96348GW
Psi size in KB : 24
Number of MAC Addresses (1-32) : 12
Base MAC Address : 00:16:38:55:d4:3e
Ethernet PHY Type : Internal
Memory size in MB : 16

*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Code Address: 0x8F08AB74, Entry Address: 0xcc36a6a9
Failed on decompression. Corrupted image?
web info: Waiting for connection on socket 0.


the settings for hyperteminal is 115200 8 bits 1 stop no parity xon/xoff

I'm using putty in serial mode

you must plug ethernet cable on port 2 then you can use the http server included
http://pix.nofrag.com/12/fe/c3d671eaaddf7662a0319bbd5e63.gif
or you can load a image from a tftp server with the command f

Once you are on CFE you can type h for getting all the commands


D'après l'ecran d'accueil du CFE on a :
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
et au niveau du help
w Write the whole image start from beginning of the flash
e Erase [n]vram or [a]ll flash except bootrom
r Run program from flash image or from host depend on [f/h] fl
ag
p Print boot line and board parameter info
c Change booline parameters
f Write image to the flash
i Erase persistent storage data
b Change board parameters
reset Reset the board
flashimage Flashes a compressed image after the bootloader.
help Obtain help for CFE commands

the PC must have the Host IP address displayed in CFE configuration
_________________

CI c'était des hommes, un service et de la qualité

[nnouveau]

je ne savais pas qu'un éléphant ca parlait bien anglais..

Je n'ai pas compris grand chose..

PS : On te voit de moins en moins.. tu imites Melo ?


_________________
Chez CI depuis 1999..

Migré automatiquement depuis le 19 Juin 2009.

Un souci suite à la migration automatique.. lisez donc les 3 SOLUTIONS APRES MIGRATION AUTOMATIQUE, cliquez
ICI

[beeptac]

great info

I have constructed the cable with l' adapter usb but do not visualize correctly the log of busybox? (not comprehensible characters) however they are successful to interrupt the boot and to enter through eth2-video to the mini-web for restore firmware.

I have loaded firmware ci-box correctly…

thank you

you know the better firmware to load?
I would want to use the voip (sip protocol) I have read several post but me it seems that the plans are stop!

[Dumboton]

I'm very glad you can unbrick your box.
About SIP, up to now Idon"t know a successful way ..in France. Where do you want to use it ?
_________________

CI c'était des hommes, un service et de la qualité

[beeptac]

i live in Italy....

I would want to use it as ATA has 2 telephone lines…